Visualization Modules

This plugin helps with early detection of generator efficiency loss and other problems. It compares real-time generator capacity and heat rates to expected values from manufacturer curves or actual historical data. Curves are customizable and can be easily adjusted at any time.

Pulp Line Condition Monitor

This plugin monitors the performance of the pulp line by comparing real-time drive motor power, water consumption, and chemical and bleaching agent consumption to design and/or expected historical values.

Water

Reverse Osmosis/Desalination Plant Monitor

Water

This plugin monitors the performance of the Reverse Osmosis/desalination plant. It analyzes fresh water production, chemical consumption and energy consumption to provide real-time indication of plant performance compared to design values.

Water

Distillation/Evaporation/ Desalination Plant Monitor

Water

This plugin monitors the performance of the distillation/evaporation/desalination plant. It analyzes freshwater production and energy consumption to provide real-time indication of plant performance compared to design values.

Rankine

Coking Battery and Oven Monitor and Totalizer

Rankine

This solution calculates and totalizes key parameters of the coking batteries and ovens.

Power & Utilities

Transmission & Distribution Losses

Power & Utilities

This plugin calculates real-time electrical losses throughout the Transmission and Distribution system across all transformers and transmission lines from the source generators to the substations.

Compressor

Reciprocating Engine Driven Compressor Condition Monitor

Compressor

This plugin facilitates early detection of compressor issues. It calculates compressor discharge pressure, work (brake horsepower), and both isentropic and polytropic efficiency then plots them in real time against scalable, dynamic reference curves that adjust with compressor speed as appropriate.

Reciprocating Engine Driver Condition Monitor

This module provides real-time actual vs. expected power output capacity and actual vs. expected efficiency based upon manufacturer specifications.

Drum Chemistry Monitor

This plugin plots real-time chemistry indications including pH vs phosphate and silica and cation conductivity vs. drum pressure against expected curves.

Heat Fuel Gas Heater Condition Monitor

This plugin performs thermodynamic calculations on the fuel gas heater, calculating the real-time duty, heat exchanger effectiveness, heat transfer coefficient, and fluid flows.

Turbine

Turbine Compressed Air Cooler Condition Monitor

Turbine

This plugin performs thermodynamic calculations on the TCA (Turbine Compressed Air) cooler, calculating the real-time duty, heat exchanger effectiveness, heat transfer coefficient, and fluid flows.

Oil & Gas

Heat Exchanger Condition Monitor

Oil & Gas

This plugin performs thermodynamic calculations on the heat exchanger tubes/fins/coils, calculating the real-time duty, heat exchanger effectiveness, heat transfer coefficient, and fluid flows, as appropriate.

Boiler

Auxiliary Boiler Efficiency & Condition Monitor

Boiler

This plugin delivers substantial insight into auxiliary boiler performance. It calculates boiler losses in real time in accordance with ASME PTC 4.1 then compares them to expected losses and overall efficiency.

Boiler

Biomass Boiler Efficiency & Performance Monitor

Boiler

This plugin calculates boiler efficiency in real time and compares it to expected boiler efficiency based on historical data.

Boiler

Boiler Efficiency and Performance

Boiler

This plugin delivers substantial insight into boiler performance. It calculates boiler losses in real time in accordance with ASME PTC 4.1 then compares them to expected losses and overall efficiency.

Compressor

Engine Driven Compressor Condition Monitor

Compressor

This plugin makes it easier to manage the performance of engine driven compressors. It calculates discharge pressure, work (brake horsepower), and both isentropic efficiency and polytropic efficiency and plots them in real time against scalable, dynamic reference curves that adjust with compressor speed.

Compressor

Turbine Driven Compressor Condition Monitor

Compressor

This plugin simplifies early identification of problems with turbine driven compressors. It calculates compressor discharge pressure, work (brake horsepower, and both include isentropic efficiency and polytropic efficiency then plots them plots them in real time against scalable, dynamic reference curves that adjust with compressor speed.

Turbine

Combustion Gas Turbine Power Curves Display (Using Existing KPIs)

Turbine

This variation of the Combustion Gas Turbine Power Curves plugin (PPI-LNG-CTG-PRF) allows users to customize the plugin with their own existing KPI tags.

Turbine

Combustion Gas Turbine Power Curves

Turbine

This plugin compares Corrected Power to Air Inlet Temperature and plots power against the Full Load Output design as well as PCD and WF curves.

Fan

Fan Condition Monitor

Fan

This plugin quickly identifies issues with fan performance. It calculates fluid power, driver/fan set efficiency, blower efficiency, and total pressure then plots them in real time against scalable, dynamic reference curves that adjust with fan speed.

Water

Blower Condition Monitor

Water

This plugin makes it easy to identify problems with blowers. It calculates fluid power, driver/fan set efficiency, blower efficiency, and total pressure then plots them in real time against scalable, dynamic reference curves that adjust with blower speed.

Oil & Gas

Turbo-Expander (Expansion Turbine) Condition Monitor

Oil & Gas

This plugin helps quickly identify potential problems with rotating equipment. It uses gas inlet and outlet conditions to calculate the power extracted by the turbo-expander, applicable efficiencies, and shaft losses.